OWNER'S MANUAL - LG Wi-Fi SOUND BAR - Sirv

Tilde Nielsen | Download | Embed to your website


Share:
Transcript:

OWNER’S MANUAL LG Wi-Fi SOUND BAR Please read this manual carefully before operating your set and retain it for future reference. MODEL SL7Y (SL7Y, SPL5B-W) www.lg.com 1901_Rev01 Copyright © 2019 LG Electronics Inc. All Rights Reserved.

Page 1

2 Getting Started Safety Information NOTICE: For safety marking information including product identification and supply ratings, please refer to the main label on the bottom or the other surface of the product. CAUTION 1 RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION concerning the Power Cord Getting Started The Power Plug is the disconnecting device. In case CAUTION: TO REDUCE THE RISK OF ELECTRIC of an emergency, the Power Plug must remain readily SHOCK DO NOT REMOVE COVER (OR BACK) accessible. NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Check the specification page of this owner’s manual to be certain of the current requirements. This lightning flash with arrowhead Do not overload wall outlets. Overloaded wall outlets, symbol within an equilateral triangle loose or damaged wall outlets, extension cords, frayed is intended to alert the user to the power cords, or damaged or cracked wire insulation presence of uninsulated dangerous are dangerous. Any of these conditions could result voltage within the product’s in electric shock or fire. Periodically examinew the enclosure that may be of sufficient magnitude to cord of your device, and if its appearance indicates constitute a risk of electric shock to persons. damage or deterioration, unplug it, discontinue use of The exclamation point within an the device, and have the cord replaced with an exact equilateral triangle is intended replacement part by an authorized service center. to alert the user to the presence Protect the power cord from physical or mechanical of important operating and abuse, such as being twisted, kinked, pinched, closed maintenance (servicing) instructions in a door, or walked upon. Pay particular attention to in the literature accompanying the product. plugs, wall outlets, and the point where the cord exits the device. WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. WARNING: Do not install this equipment in a confined space such as a book case or similar unit. CAUTION: Do not use high voltage products around this product. (ex. Electrical swatter) This product may malfunction due to electrical shock. CAUTION: The apparatus should not be exposed to water (dripping or splashing) and no objects filled with liquids, such as vases, should be placed on the apparatus. CAUTION: Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from over heating. The openings should never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product shall not be placed in a built- in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instruction has been adhered to. CAUTION: No naked flame sources, such as lighted candles, should be placed on the apparatus.

Page 2

Getting Started 3 CAUTION: Only use the AC adapter supplied with Symbols this device. Do not use a power supply from another device or another manufacturer. Using any other ~ Refers to alternating current (AC). power cable or power supply may cause damage to the device and void your warranty. 0 Refers to direct current (DC). 1 Refers to class II equipment. Getting Started 1 Refers to stand-by. ! Refers to “ON” (power). Refers to dangerous voltage.

Page 3

4 Table of Contents Table of Contents 1 Getting Started 2 Connecting 2 Safety Information 15 Organizing cables (Optional) 6 Introduction 15 Connecting the AC Adapter 7 Front panel 16 Wireless subwoofer and rear speaker (Sold 8 Rear panel Separately) connection 9 Remote control 16 – Wireless subwoofer connection 12 Installing the sound bar 17 – Rear speakers connection (Sold 13 Mounting the main unit on a wall Separately) 19 – Surround sound 21 Connecting to your TV 21 – Using an OPTICAL cable 21 – LG Sound Sync 23 – Using an HDMI cable 23 – ARC (Audio Return Channel) function 23 – What is SIMPLINK? 24 – Additional information for HDMI 25 Optional equipment connection 25 – HDMI connection 25 – OPTICAL IN connection 26 – USB connection 26 – Compatible USB devices 27 – USB device requirement 27 – Playable file 29 Network connection 30 “LG Wi-Fi Speaker” 30 – Installing “LG Wi-Fi Speaker” App 30 Works with the Google Assistant

Page 4

Table of Contents 5 1 3 Operating 4 Troubleshooting 31 Using a Bluetooth Wireless Technology 39 Troubleshooting 31 – About Bluetooth 39 – General 31 – Bluetooth profiles 41 – Network 2 31 – Listening to Music of a Bluetooth Device 41 – Application 33 – Controls connected Bluetooth device 42 – NOTES to use wireless 33 – Bluetooth connection lock (BT LOCK) 42 – NOTES to release Demo mode 34 USB operations 35 Other operations 5 Appendix 3 35 – Using your TV remote control 36 – AUTO POWER On/Off 43 File requirement 37 – Auto function change 43 Trademarks and licenses 38 Standby mode 44 Specifications 38 – Standby mode 46 Handling the Speaker 4 38 – Network standby mode 46 Important Information Relating to Network 38 – Bluetooth standby mode Services 38 Reset the Speaker 47 TERMS OF USE 5 Some of the content in this manual may differ from “LG Wi-Fi Speaker” app depending on the application’s version.

Page 5

6 Getting Started Introduction Symbol used in this manual 1 ,,Note Getting Started Indicates special notes and operating features. >>Caution Indicates cautions for preventing possible damages from abuse.

Page 6

Getting Started 7 Front panel 1 Getting Started A Remote sensor Display Window B -- Display window will be darkened automatically if there is no key input for 15 seconds. When you press any button, the display window will brighten. 1 (Standby) -- Switches the unit ON or OFF. F (Function) -- Select the function and input source by pressing F repeatedly. Input source / Function Display Wi-Fi WI-FI Optical ARC OPT/HDMI ARC C LG Sound Sync (Wired) Bluetooth BT LG Sound Sync (Wireless) LG TV HDMI IN HDMI USB USB o/p (Volume) -- Adjusts volume level. (Wi-Fi) -- Selects Wi-Fi function. , This unit will turn itself off to save electric consumption when the main unit is not connected to an external device and is not used for 15 minutes. When network is connected, the speaker switches to the network standby mode. If network is disconnected, the speaker switches to the standby mode.

Page 7

8 Getting Started Rear panel 1 Getting Started DC IN A -- Connect to the AC adapter. USB Port B -- Connect USB memory device to the USB port on the back of the unit. OPTICAL IN C -- Connect the OPTICAL IN jack on the back of the unit to OPTICAL OUT jack on the TV. HDMI IN D -- Connect HDMI IN jack on the back of the unit to HDMI OUT jack on the external device. You can enjoy the sound and picture from HDMI connection on an external device. (TV ARC) HDMI OUT E -- Connect the (TV ARC) HDMI OUT jack on the back of the unit to ARC jack on the TV.

Page 8

Getting Started 9 Remote control Replacement of Battery 1 Remove the battery cover on the rear of the remote Getting Started control, and insert the battery with 4 and 5 matched correctly. 1 (Standby) -- Switches the unit ON or OFF. a yy Network Standby On/Off: It allows the unit to switch to standby mode while maintaining a network connection. (Page 38) To turn on Network Standby function, Press 1. To turn off Network Standby function, press 1 for about 3 seconds. VOL (Volume) o/p b -- Adjusts speaker volume. C/V (Skip) c -- Press C or V to go to next or previous file. N (Play/Pause) -- Starts playback. / Pauses playback. d yy BT (Bluetooth) connection Lock: It allows you to connect a Bluetooth device only on Bluetooth and LG TV functions. (Page 33) To turn on or off the Bluetooth connection lock, press and hold N for about 3 seconds and press it again in BT (Bluetooth) function.

Page 9

10 Getting Started SOUND EFFECT -- Selects a sound effect mode by using SOUND EFFECT. On Display Description 1 Analyzes the property of the input sound and provides the ASC (Adaptive Sound Control) Getting Started sound optimized for the content in real time. BASS BLAST or BASS BLAST+ Reinforces the bass and powerful sound. STANDARD You can enjoy optimized sound. e DTS VIRTUAL: X You can enjoy more immersive and cinematic surround sound. yy TV remote: It allows you to control the volume of this unit by your TV remote control even by other company’s product. (Page 35) To turn on or off the TV Remote function, press and hold SOUND EFFECT for about 3 seconds and press it again. , Supported TV brands LG Panasonic Philips Samsung Sharp Sony Toshiba Vizio (Sound tuning) -- Adjusts sound level of each speaker. Select the speaker you want to adjust by using and adjust the sound level by using VOL o/p. , Adjusting rear speakers level is applied only when the rear speakers are connected. Speaker Display Range Sub Woofer WF -15 ~ 6 f Center C -6 ~ 6 Rear R -6 ~ 6 Treble TRE -5 ~ 5 Bass BAS -5 ~ 5 yy Surround sound: It allows you to enjoy surround sound with rear speakers. (Page 19) To turn on or off the surround sound, press and hold for about 3 seconds and press it again.

Page 10

Getting Started 11 F (Function) g -- Select the function and input source by pressing F repeatedly. [ (Mute) h -- Press [ to mute your unit. To cancel it, press [ again. 1 Getting Started J (Information) -- You can display various information of the input source by pressing J. -- OPT (Optical)/ARC/HDMI (HDMI IN): Audio format -- BT (Bluetooth): Connected Bluetooth device name -- USB: File information contained on a USB. i yy Auto Power ON/OFF: It allows the unit to turn on and off automatically by input signals: Optical, LG TV, Bluetooth or “LG Wi-Fi Speaker” app (Page 36) To turn on or off AUTO POWER function, press and hold J for about 3 seconds and press it again. yy BT Standby On/Off: It allows the unit to switch to standby mode while maintaining Bluetooth connection. (Page 38) To turn on or off BT Standby function, set the volume to a minimum in advance. Press and hold p on the unit and J on the remote control for about 3 seconds and then press J again. REPEAT j -- Press REPEAT to select desired repeat or random mode. FOLDER W/S k -- Searches a folder on USB device.

Page 11

12 Getting Started Installing the sound bar >>Caution yy For best performance of wireless connection such as Bluetooth or wireless subwoofer, You can hear the sound by connecting the unit to the do not install the unit on Metallic furniture 1 other device: TV, Blu-ray disc player, DVD player, etc. because wireless connection communicates Place the unit in front of the TV and connect it to the through a module positioned on the bottom Getting Started device you want. (Pages 21 - 29) of the unit. You can place the wireless subwoofer anywhere in yy Be careful not to make scratches on the your room. But it is better to place the subwoofer surface of the Unit /Subwoofer when near the main unit. Turn it slightly toward the center installing or moving them. of the room to reduce the wall reflections. For the best surround sound, place the speakers as Installing the additional foot shown below. You can extend the height of the unit by using additional foot (height: 14 mm). 1. Turn the unit upside down. 2. Peel off a sticker attached to the additional foot. Then place it on the existing foot of the unit. 3. Press the additional foot with adequate force to get it firmly fixed. ,,Note yy If the sound bar covers the remote sensor of the TV, please separate distance between the sound bar and TV by 10 ~ 15 cm or more. yy The illustration above may differ from actual units. yy You can enjoy surround sound by using Wireless Rear Speaker kit. Wireless Rear Speakers Kit sold separately (SPK8-S).

Page 12

Getting Started 13 Mounting the main unit 1. Match the TV’s BOTTOM EDGE of Wall bracket install guide with the bottom of TV and attach to on a wall the position. 1 You can mount the main unit on a wall. Getting Started 2. When you mount it on a wall (concrete), use the wall plugs. You should drill some holes. A guide >>Caution sheet (Wall bracket install guide) is supplied to drill. Use the sheet to check the point to drill. Because it is difficult to make a connection after installing this unit, you should connect the cables before installation. Preparation materials Unit Wall bracket install guide 3. Remove the Wall bracket install guide. Wall bracket 4. Fix the brackets with screws (A) as shown in the illustration below. Screws (Not supplied) Screws (A) Wall plug ,,Note Screws (A) and Wall Plugs are not supplied for mounting the unit. We recommend the Hilti (HUD-1 6 x 30) for the mounting.

Page 13

14 Getting Started 5. Put the unit on the brackets to match screw holes on the bottom of the unit. 1 Getting Started 6. Fix the unit with the screws firmly. ,,Note To detach the unit, perform it in reverse order. >>Caution yy Do not install this unit upside down. It can damage the parts of this unit or be the cause of personal injury. yy Do not hang onto the installed unit and avoid any impact to the unit. yy Secure the unit firmly to the wall so that it does not fall off. If the unit falls off, it may result in an injury or damage to the product. yy When the unit is installed on a wall, please make sure that a child does not pull any of connecting cables, as it may cause it to fall.

Page 14

Connecting 15 Organizing cables Connecting the AC (Optional) Adapter You can organize the cable with cable ties. Connect the sound bar to the power supply with the supplied AC adapter. 1. Hold the cables together with cable ties as shown below. 1. Connect the supplied AC power cord to the AC 2. Tighten cable ties. adapter. 2. Connect the AC adapter cable to DC IN adapter 2 input. Connecting 3. Plug the AC power cord into an AC outlet. ,,Note yy After all connections are completed, you can arrange cables as needed. yy Cable ties are not supported. >>Caution Only use the AC adapter supplied with this device. Do not use a power supply from another device or manufacturer. Using any other power cable or power supply may cause damage to the device and void your warranty.

Page 15

16 Connecting Wireless subwoofer Manually pairing wireless subwoofer When your connection is not completed, you can and rear speaker (Sold check red LED on the wireless subwoofer and the wireless subwoofer does not make sound. To solve Separately) connection the problem, follow the steps below. 1. Press Pairing on the rear of the wireless subwoofer. Wireless subwoofer connection 2 LED indicator of wireless subwoofer Connecting LED Color Status Green The connection is trying. (Blink) -- The green LED on the rear of the wireless Green The connection is completed. subwoofer blinks quickly. (If the green LED does not blink, press and hold Red The wireless subwoofer is in the Pairing.) standby mode or the connection is failed. 2. Turn on the sound bar. Off (No The power cord of wireless -- Pairing is completed. The green LED on the rear display) subwoofer is disconnected. of the wireless subwoofer turns on. Setting up the wireless subwoofer for the first time 1. Connect the power cord of the sound bar and the wireless subwoofer to the outlet. 2. Turn on the sound bar. The sound bar and the wireless subwoofer will be automatically connected. -- Green LED on the rear of wireless subwoofer turns on.

Page 16

Connecting 17 ,,Note Rear speakers connection (Sold yy It takes a few seconds (and may take longer) for the main unit and the subwoofer to Separately) communicate with each other and make sounds. Connecting the rear speakers yy The closer the main unit and the subwoofer, 1. Connect the black stripe wire to the terminal the better sound quality. It is recommended marked - (minus) and the other end to the to install the main unit and the subwoofer as terminal marked + (plus). close as possible and avoid the cases below. -- There is an obstacle between the main unit 2 and the subwoofer. Connecting -- There is a device using same frequency with this wireless connection such as a medical equipment, a microwave or a wireless LAN device. -- Keep the sound bar and the subwoofer away from the device (ex. wireless router, microwave oven, etc.) over 1 m to prevent wireless interference. !1 m 2. Connect the wireless receiver and the rear speakers (right, left) with the speaker cables. Color Position Grey Rear right Blue Rear left ,,Note You need to purchase the wireless rear speakers kit (SPK8-S) to enjoy surround sound.

Page 17

18 Connecting >>Caution Manually pairing wireless receiver yy Use the speaker supplied with this unit When your connection is not completed, you can only. Using any other speaker may cause see the red LED on the wireless receiver and rear malfunction. speakers do not make sound. To solve the problem, yy Be sure to match the speaker cable to the follow the below steps. appropriate terminal on the components: + 1. Press PAIRING on the rear of the wireless to + and – to –. If the cables are reversed, the receiver. sound will be distorted and will lack bass. 2 LED indicator of wireless receiver Connecting LED Color Status Yellow - green The connection is trying. (Blink) Yellow - green The connection is completed. -- The yellow - green LED on the wireless receiver blinks quickly. Red The wireless receiver is in standby mode or the connection is failed. 2. Turn on the main unit -- Paring is completed. The yellow - green LED on Off The power cord of wireless the wireless receiver turns on. (No display) receiver is disconnected. Setting up the wireless receiver for the first time 1. Connect the power cord to the wireless receiver to the outlet. 2. Turn on the main unit: The sound bar and wireless receiver will be automatically connected. -- Yellow - green LED on the wireless receiver turns on.

Page 18

Connecting 19 Surround sound ,,Note yy If there is a strong electromagnetic wave You can enjoy magnificent surround sound for all the product nearby, interference may occur. Put input sound source with rear speakers. the main unit and wireless receiver away from If you turn on the surround function, the whole there. speaker outputs sound. yy The wireless receiver will automatically switch When you turn off the surround function, the to standby mode in a few minutes after the speakers output sound as an original input sound sound bar is turned off. channel. When the wireless receiver is in standby To turn on surround function, press and hold on mode, the LED will turn on in red. 2 the remote control for about 3 seconds and press it yy When you turn on the sound bar, the wireless once again while “OFF - SURROUND” is scrolled. Connecting receiver will turn on and the LED will change To turn off surround function, press and hold on to yellow - green and then the rear speakers the remote control for about 3 seconds and press it makes sound within a few seconds. once again while “ON - SURROUND” is scrolled. yy It takes a few seconds (and may take longer) for the main unit and Wireless Receiver to communicate with each other. yy Use the rear speaker at least 30 cm away from either TV screen or PC monitor. yy When the wireless receiver is being connected or disconnected with the main unit, output sound may be interrupted. yy Set the distance between the sound bar and the wireless receiver as close as possible and keep them away from the device (ex. wireless router, microwave oven, etc.) over 1 m to prevent wireless interference. !1 m

Page 19

20 Connecting Surround function ON Output Sound Effect Input No rear speakers Rear speakers connected 2.0 Ch ASC 5.1 Ch 2 2.0 Ch STANDARD Connecting 5.1 Ch BASS BLAST 2.0 Ch or BASS BLAST + 5.1 Ch 2.0 Ch DTS VIRTUAL: X 5.1 Ch Surround function OFF Output Sound Effect Input No rear speakers Rear speakers connected 2.0 Ch ASC 5.1 Ch 2.0 Ch STANDARD 5.1 Ch BASS BLAST 2.0 Ch or BASS BLAST + 5.1 Ch 2.0 Ch DTS VIRTUAL: X 5.1 Ch

Page 20

Connecting 21 Connecting to your TV LG Sound Sync Please connect with this unit and TV using the optical digital cable or HDMI cable considering the state of the TV. You can control some functions of this unit by your TV’s remote control with LG Sound Sync. It is Using an OPTICAL cable compatible with the LG TV that is supported LG Sound Sync. Make sure of the LG Sound Sync logo on 1. Connect the OPTICAL IN jack on the back of the your TV. unit to OPTICAL OUT jack on the TV using an 2 Controllable function by LG TV’s remote control: OPTICAL cable. Volume up/down, mute Connecting Refer to the TV’s instruction manual for the details of LG Sound Sync. Make one of the following connections, depending on the capabilities of your equipment. Optical cable ,,Note yy You can also use the remote control of this unit while using LG Sound Sync. If you use TV’s remote control again, the unit synchronizes with the TV. According to TV Specifications, the volume and mute of this unit synchronize with TV. 2. Select the input source to OPT/HDMI ARC by pressing F repeatedly. yy When the connection fails, make sure of the condition of the TV and power. You can see “OPT” on the display window if connecting normally between this unit and your yy Make sure of the condition of this unit and TV. the connection in the cases below when using LG Sound Sync. ,,Note -- The unit is turned off. yy Before connecting the optical cable, be sure -- Changing the function to the others. to remove the protection plug cover if your cable has the cover. -- Disconnecting the optical cable. yy You can enjoy the TV audio through the yy The amount of time to turn off this unit is speakers of this unit. In the case of some TV different depending on your TV when you set models, you must select the external speaker AUTO POWER function to ON. option from the TV menu. (For details, reference your TV user manual.) yy Set up the sound output of TV to listen to the sound through this unit: TV setting menu [ [Sound] [ [TV Sound output] [ [External speaker (Optical)] yy Details of TV setting menu vary depending on the manufacturers or models of your TV. yy If this unit is connected by OPTICAL and ARC at the same time, the ARC signal is a high priority.

Page 21

22 Connecting LG Sound Sync with wired connection LG Sound Sync with wireless 1. Connect your LG TV to the unit by using an connection optical cable. 1. Turn on the unit by pressing 1. 2. Select the LG TV function by pressing F repeatedly. 3. Set up the sound output of TV to listen to the sound through this unit: Optical cable TV setting menu [ [Sound] [ [TV Sound 2 output] [ [LG Sound Sync (Wireless)] “PAIRED” appears on the display window for Connecting about 3 seconds and then you can see “LG TV” on the display window if connecting normally between this unit and your TV. 2. Set up the sound output of TV to listen to the ,,Note sound through this unit: yy If you turned off the unit directly by pressing TV setting menu [ [Sound] [ [TV Sound 1 (Power), LG Sound Sync (Wireless) will be output] [ [LG Sound Sync (Optical)] disconnected. 3. Turn on the unit by pressing 1. yy If your TV and this unit are connected through LG Sound Sync (Wireless), this unit will be 4. Select the input source to OPT/HDMI ARC by Network standby mode regardless of the pressing F repeatedly. status of network connection when this unit You can see “LGOPT” on the display window if is turned off. connecting normally between this unit and your TV. ,,Note Details of TV setting menu vary depending on the models of your TV.

Page 22

Connecting 23 Using an HDMI cable ARC (Audio Return Channel) If you connect this unit to a TV that supports HDMI function CEC and ARC (Audio Return Channel), you can The ARC function enables an HDMI capable TV to enjoy the TV audio through the speakers of this unit send the audio stream to HDMI OUT of the unit. without connecting the optical cable. To use this function: 1. Connect the (TV ARC) HDMI OUT jack on the -- Your TV must support the HDMI-CEC and ARC back of the unit to ARC jack on the TV using an function and the HDMI-CEC and ARC must be set HDMI cable. to On. -- The setting method of HDMI-CEC and ARC may 2 differ depending on the TV. For details about ARC Connecting function, refer to your TV manual. -- You must use the HDMI cable (Type A, High Speed HDMI cable HDMI™ cable with Ethernet). -- You must connect the HDMI OUT on the unit with HDMI IN of the TV that supports ARC function using an HDMI cable. -- You can connect only one Sound bar to TV compatible with ARC. 2. Select the input source to OPT/HDMI ARC by pressing F repeatedly. You can see “ARC” on the display window if What is SIMPLINK? connecting normally between this unit and your TV. ,,Note yy You can enjoy the TV audio through the Some functions of this unit are controlled by the speakers of this unit. In the case of some TV TV’s remote control when this unit and LG TV’s with models, you must select the external speaker SIMPLINK are connected through HDMI connection. option from the TV menu. (For details, reference your TV user manual.) Controllable functions by LG TV’s remote control: Power on/off, volume up/down, etc. yy Set up the sound output of TV to listen to the sound through this unit: Refer to the TV owner’s manual for the details of TV setting menu [ [Sound] [ [TV Sound SIMPLINK function. output] [ [External speaker (HDMI ARC)] LG TV’s with SIMPLINK function has the logo as shown above. yy Details of TV setting menu vary depending on the manufacturers or models of your TV. ,,Note yy Depending on your LG TV model, you may yy Depending on the state of the unit, some need to turn on the SIMPLINK function on SIMPLINK operation may differ from your your LG TV. purpose or not work. yy When you return to ARC function from yy Depending on a TV or a player which is another function, you need to select the input connected with this unit, SIMPLINK operation source to OPT/HDMI ARC. Then this unit may differ from your purpose. changes to ARC function automatically.

Page 23

24 Connecting Additional information for HDMI HDMI cable Checklist yy When you connect an HDMI or DVI compatible Some HDMI cables have poor signal transmission, device make sure of the following: which can cause problems with sound and video transmission. - Try switching off the HDMI/DVI device and this player. Next, switch on the HDMI/DVI device and Even after HDMI cable connections, if no sound, leave it for around 30 seconds, then switch on sound interrupted, noise occurring from the sound this player. bar and/or no video, no smooth video on your TV, the HDMI cable may be the problem. - The connected device’s video input is set correctly for this unit. Use the cable marked with the premium HDMI 2 certification logo. Also make sure that the your - The connected device is compatible with using cable is a certified Type A, Ethernet high-speed Connecting 720 x 576p (or 480p), 1280 x 720p, HDMI™ cable. 1920 x 1080i, 1920 x 1080p video input. yy Not all HDCP-compatible HDMI or DVI devices will (X) STANDARD HDMI CABLE WITH ETHERNET work with this player. - The picture will not be displayed properly with HIGH SPEED HDMI CABLE (X) non-HDCP device. (O) ,,Note HIGH SPEED HDMI CABLE WITH ETHERNET yy If a connected HDMI device does not accept the audio output of the player, the HDMI Connection through HDMI Cable* device’s audio sound may be distorted or may Your television must support the newest HDMI not output. features (HDMI CEC1) / ARC (Audio Return Channel)) yy Changing the resolution when the connection to fully enjoy the Live broadcasting channel with has already been established may result in audio system through an HDMI cable. Unless your malfunctions. To solve the problem, turn off TV supports these HDMI features, the audio system the player and then turn it on again. should be connected through an OPTICAL cable. yy When the HDMI connection with HDCP is not 1) HDMI CEC (High-Definition Multimedia Interface verified, TV screen is changed to black screen. Consumer Electronics Control) In this case, check the HDMI connection, or Consumer Electronics Control (CEC) is an HDMI disconnect the HDMI cable. feature designed to allow the user to command and yy If there are noises or lines on the screen, control the CEC-enabled devices, that are connected please check the HDMI cable (length is through HDMI by using only one of their remote generally limited to 4.5 m). controls. yy You cannot change the video resolution in the * Trade names for CEC are SimpLink (LG) , Anynet+ HDMI mode. Change the video resolution of (Samsung), BRAVIA Sync (Sony), EasyLink (Philips), the connected component. etc. yy If the video output signal is abnormal when your personal computer is connected to HDMI IN jack, change the resolution of your personal computer to 576p (or 480p), 720p, 1080i or 1080p.

Page 24

Connecting 25 Optional equipment OPTICAL IN connection connection Connect an optical output jack of external devices to the OPTICAL IN jack. HDMI connection You can enjoy the sound from the external device which is connected to HDMI IN jack on this unit. Optical cable 2 Connecting To the optical output jack of external device 1. Connect the OPTICAL IN jack on the back of the unit to optical out jack of your external device. 2. Select the input source to OPT/HDMI ARC by pressing F repeatedly. You can see “OPT” on the display window if connecting normally between this unit and your device. To the Blu-ray disc player, DVD player, etc. ,,Note Before connecting the optical cable, be sure to 1. Connect HDMI IN jack on the back of the unit to remove the protection plug cover if your cable HDMI OUT jack on the audio device such as Blu- has the cover. ray disc player, DVD player, etc. 2. Select the input source to HDMI by pressing F repeatedly.

Page 25

26 Connecting Optional equipment connection USB connection You can enjoy both sound and picture from the Connect USB memory device to the USB port on the external device you connect. back of the unit. 2 Connecting OR For more information of playing files on a USB, refer to the page 34. Removing the USB Device from the unit. 1. Choose a different function/mode. 2. Remove the USB device from the unit. 1. Connect HDMI IN jack of your TV to HDMI OUT jack on the external device such as Blu-ray disc player, DVD player, etc. ,,Note It is recommended that you purchase a 2. Connect the OPTICAL IN jack on the back of the USB gender separately for the convenience unit to OPTICAL OUT jack on the TV using an of USB insertion and extraction. OPTICAL cable. (Recommended USB gender type: USB 2.0 Or connect the (TV ARC) HDMI OUT jack on the extension cable) back of the unit to HDMI IN (ARC) jack on the TV using an HDMI cable. 3. Select the input source to OPT/HDMI ARC by Compatible USB devices pressing F repeatedly. yy MP3 Player: Flash type MP3 player. yy USB Flash Drive: Devices that support USB 2.0. ,,Note yy The USB function of this unit does not support If the sound bar does not have sound or the some USB devices. video on TV is not smooth, the HDMI cable may be the problem. Refer to the HDMI cable checklist. (Page 24)

Page 26

Connecting 27 USB device requirement Playable file yy Devices which require additional program Sampling Frequency installation connected to a computer, are not MP3: within 32 to 48 kHz supported. WMA:within 32 to 48 kHz. yy Do not extract the USB device while in operation. OGG: within 32 to 48 kHz yy For a large capacity USB, it may take longer than a FLAC:32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, few minutes to be searched. 176.4 kHz and 192 kHz (16 bit/ 24 bit) yy To prevent data loss, back up all data. WAV: 32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz and 192 kHz (16 bit/ 24 bit) yy This unit recognizes up to 2,000 files. 2 yy The unit’s USB Port cannot be connected to PC. Bitrate resolution Connecting The unit can not be used as a storage device. MP3: within 80 to 320 kbps yy FAT16/FAT32/NTFS file system is supported on WMA: within 56 to 128 kbps this unit. OGG: within 64 to 500 kbps yy Depending on some devices, it may not available to recognize the followings on this unit. yy Maximum files: Up to 2,000 -- External HDD yy Maximum directories: Up to 200 -- Card readers yy A protected file by DRM (Digital rights -- Locked devices management) cannot be played on the unit. -- Hard type USB devices yy Video files in the USB storage device can not be played. -- USB hub yy Depending on the performance of your USB -- Using USB extension cable device, playback may not work well. -- iPhone/iPod/iPad -- Android device

Page 27

28 Connecting ,,Note yy Folders and files on the USB are recognized as below. : Folder : File a C D 2 E Connecting b F G c H I d J A B yy If there is no file in a folder, the folder will not appear. yy File will be played from file $A to file $J one by one. yy Files will be played in order recorded and it may be different depending on the record circumstances. yy This unit can display file or folder names that contain numbers or English characters only. yy *ROOT: The first screen you can see when a this unit recognize the USB is “ROOT”.

Page 28

Connecting 29 Network connection You can enjoy various functions of this sound bar by connecting to network and your smart device with “LG Wi-Fi Speaker” app. ,,Note Modem Server In a network environment (Router, Internet and Internet Service Provider) that supports both IPv4 and IPv6, the network automatically 2 connects to IPv4 or IPv6 when connecting to Connecting the network. You can check the each network status Router by selecting the settings of My Speakers ([Settings]>[IP Info.]) on the “LG Wi-Fi Speaker” app. The “LG Wi-Fi Speaker” app is required to connect the sound bar wirelessly to the network. Download and install the “LG Wi-Fi Speaker” app on your smart device. Launch the application and follow the instructions on the screen of your smart device, so that you can connect the sound bar wirelessly.

Page 29

30 Connecting “LG Wi-Fi Speaker” Installing “LG Wi-Fi Speaker” App The “LG Wi-Fi Speaker” app allows you to use various functions of this sound bar through your smart Through “App Store” or “Google Play” device: 1. Tap the “App Store” icon or “Google Play” icon. Enjoying music on your device and 2. Type in “LG Wi-Fi Speaker” in the search bar and home network server tap “Search”. 3. Select “LG Wi-Fi Speaker” in the search result list 2 You can listen to the music on your smart device and to download. home network server. ,,Note Connecting Using Chromecast built-in yy “LG Wi-Fi Speaker” app will be available in You can enjoy music contents through this sound bar version of the software as follow; with Chromecast enabled apps. Android OS: Ver 5.0 (or later) iOS: Ver 10 (or later) Setting and controlling the sound bar yy Depending on the device, “LG Wi-Fi Speaker” You can manage the sound bar settings and control app may not work. the sound bar even without remote control. yy You can find the available application of this unit by using “LG Audio” app. Android OS: Ver Updating the sound bar 5.0 (or later) You can update the sound bar to the latest version. Requirements yy A wireless router must be connected to the Works with the Google internet. yy A smart device such as a smartphone or tablet Assistant must be connected to the wireless router via Wi- Fi connection. This unit works with the Google Assistant. You can control some functions of this unit: Play and stop ,,Note music and volume control. For more informations of “LG Wi-Fi Speaker”, follow the instructions of the application or see Requirements the owner’s manual of “LG Wi-Fi Speaker”. yy Google Assistant built-in device (Sold Separately) yy This unit must be connected to Internet. yy This unit must be registered in [Google Home] app.

Page 30

Operating 31 Using a Bluetooth Listening to Music of a Bluetooth Device Wireless Technology Before you start the pairing procedure, make sure that the Bluetooth feature on your smart device is turned on. Refer to your Bluetooth device’s user About Bluetooth guide. Once a pairing operation is performed, it does Bluetooth is wireless communication technology for not need to be performed again. short range connection. 1. Select the Bluetooth function by using F until the The sound may be interrupted when the connection function is selected. interfered by the other electronic wave or you Appears “BT” and then “READY” in display connect the Bluetooth in the other rooms. window. Connecting individual devices under Bluetooth 2. Operate the Bluetooth device and perform wireless technology does not incur any charges. A the pairing operation. When searching for this mobile phone with Bluetooth wireless technology speaker on your Bluetooth device, a list of the 3 can be operated via the Cascade if the connection devices found may appear in the Bluetooth was made via Bluetooth wireless technology. device display depending on the type of Operating yy Available Devices: Smart phone, MP3, Notebook, Bluetooth device. etc. Your speaker appears as “LG SL7Y (XX:XX)”. yy Version: 4.0 3. Select the “LG SL7Y (XX:XX)”. yy Codec: SBC, AAC ,,Note yy XX:XX means the last four digits of Bluetooth profiles address. For example, if your unit has a MAC address such as 20:C3:8F:C9:31:55, In order to use Bluetooth wireless technology, you will see “LG SL7Y (31:55)” on your devices must be able to interpret certain profiles. This Bluetooth device. speaker is compatible with following profile. yy Depending on the Bluetooth device type, A2DP (Advanced Audio Distribution Profile) some devices have a different pairing way. For details about Bluetooth pairing, refer to your Bluetooth device manual.

Page 31

32 Operating 4. When this unit is successfully connected with ,,Note your Bluetooth device, yy This unit supports Bluetooth auto pairing. “PAIRED” [ your device’s name [ “BT” appears However it does not operate in the case on the display window. below: ,,Note -- When you restart this unit. yy If it is unavailable to display device name -- When you disconnect this unit by yourself. on the unit, “-” will be displayed. -- When you disconnect this unit on the yy To check the connected device’s name, connected Bluetooth device. press J on the remote control. The yy The sound may be interrupted when the connected Bluetooth device’s name is connection is interfered with by the some displayed. other electronic wave. yy You cannot control the Bluetooth device with 5. Listen to music. this unit. To play music in your Bluetooth device, refer to yy Pairing is limited to “One” Bluetooth device. 3 your Bluetooth device’s user guide. Multi-Pairing is not supported. According to your Bluetooth device’s volume level, yy Depending on the type of the device, you may Operating the volume level of Bluetooth will be adjusted. not be able to use the Bluetooth function. ,,Note yy You can enjoy using Bluetooth when using yy When using Bluetooth technology, you have Phone, MP3, Notebook, etc.. to make a connection between the unit and yy The more distance between the unit and the the Bluetooth device as close as possible and Bluetooth device, the lower the sound quality keep the distance. becomes. However it may not work well in the case below: yy Bluetooth connection will be disconnected when the unit is turned off or the Bluetooth -- There is an obstacle between the unit and device gets to far from the unit. the Bluetooth device. yy If the Bluetooth connection is disconnected, -- There is a device using same frequency connect the Bluetooth device again. with Bluetooth technology such as a medical equipment, a microwave or a yy When a Bluetooth device is not connected, “READY” appears on the display window. wireless LAN device. yy If you set the WI-FI function in the state of unconnected network, Bluetooth and Wireless TV Sound Sync may not be connected. yy If you change to another function after connecting Bluetooth device, Bluetooth connection will be disconnected. And you return to Bluetooth function, Bluetooth connection will be connected automatically.

Page 32

Operating 33 Controls connected Bluetooth device You can control the connected Bluetooth device from the unit; play, pause, skip, volume. ,,Note yy Only Android OS and iOS is available to use this function. yy This function may not be supported depending on the Bluetooth device or some of TV operated differently. Bluetooth connection lock (BT 3 LOCK) Operating You can limit Bluetooth connection to only BT (Bluetooth) and LG TV function to prevent unintended Bluetooth connection. To turn on this function, press and hold N on the remote control for about 3 seconds in BT (Bluetooth) function and press it once again while “OFF - BT LOCK” is scrolled. Then you can limit Bluetooth connection. To turn off this function, press and hold N on the remote control for about 3 seconds in BT (Bluetooth) function and press it once again while “ON - BT LOCK” is scrolled. ,,Note Even if you set up BT LOCK function to On, this sound bar turns on by Auto Power function. Turn off Auto Power function to prevent it. (Page 36)

Page 33

34 Operating USB operations ,,Note yy The resume point may be cleared when you pull out the power cord or removing the USB 1. Connect the USB device to the USB port. device from the unit. 2. Select the USB function by pressing F repeatedly. yy Repeat/Random playback operates as follows. To Do this On Display Description Press N on the remote Playback OFF Plays songs on USB device control. in order. During playback, press N on Pause ONE Plays a same song the remote control. repeatedly. During playback, press V on FOLDER Plays songs in a folder the remote control to go to the repeatedly. next file. 3 Playing less than 3 seconds, ALL Plays all the songs on USB Skip to the next/ press C on the remote device repeatedly. Operating previous file control to go to the previous file. SHUFFLE Plays all the songs once Playing after 3 seconds, press randomly, and stops the C on the remote control to playback. go to the beginning of the file. Press REPEAT on the remote Play repeatedly control repeatedly. Refer to or randomly the note for details about the display change. Press FOLDER W/S� Search a folder on the remote control.

Page 34

Operating 35 Other operations Using your TV remote control You can control some functions of this unit by your TV remote control even by other company’s product. Controllable functions are volume up/down and mute. Press and hold SOUND EFFECT on the remote control for about 3 seconds. “ON - TV REMOTE” appears and you can control this unit by your TV remote control. To check the status of this function, press and hold SOUND EFFECT on the remote control. 3 To turn off this function, press and hold SOUND Operating EFFECT on the remote control and press it once again while “ON - TV REMOTE” is scrolled. ,,Note yy Make sure that the sound output of your TV is set to [External speaker]. yy This function does not operate on LG TV’s magic remote control. yy This function may not work well when some TV control functions such as HDMI CEC, SIMPLINK and LG Sound Sync set to ON. yy Some remote control may not be supported.

Page 35

36 Operating AUTO POWER On/Off ,,Note yy After the unit is turned on by AUTO POWER This sound bar automatically turns on and off by an function, it will be automatically turned off if input source: Optical, LG TV, Bluetooth or “LG Wi-Fi there is no signal for a certain period of time Speaker” app. from the TV connected by LG Sound Sync To turn on this function, press and hold J on the (Optical/Wireless). remote control for about 3 seconds and press it once yy After the unit is turned on by AUTO POWER again while “OFF - AUTO POWER” is scrolled. function, it will be automatically turned off if To check the status of this function, press and hold there is no signal for a certain period of time J on the remote control. from the external device. To turn off this function, press and hold J on the yy If you turned off the unit directly, it cannot remote control for about 3 seconds and press it once be turned on automatically by AUTO POWER again while “ON - AUTO POWER” is scrolled. function. However the unit can be turned on by AUTO POWER function when optical signal Turning on comes in after 5 seconds of no signal. 3 Turning on automatically by this function is supported yy Depending on the connected device, this only on network standby mode except an optical function may not operate. Operating signal. yy If you disconnect Bluetooth connection by When you turn on your TV or an external device this unit, some Bluetooth devices try to connected to this unit, this unit recognizes the input connect to the unit continually. Therefore it is signal and selects the suitable function. You can hear recommended to disconnect the connection the sound from your device. before turning off the unit. If you try to connect your Bluetooth device, this yy When you turn on this unit for the first time, unit turns on and the unit will be connected to your status of Auto Power function is turned on. Bluetooth device. yy To use this function, the main unit must be When you run the “LG Wi-Fi Speaker” app and play registered in paired devices list of Bluetooth music on your smart device that has already been device. paired, the sound bar is turned on to Wi-Fi function yy You can set the Auto Power function only and you can listen to the music through the sound when this unit is turned on. bar Turning off When the TV is off, this sound bar switches to the standby mode.

Page 36

Operating 37 Auto function change ,,Note yy This unit does not change the function to This sound bar recognizes input signals such as optical if SIMPLINK of the connected TV, Optical, HDMI ARC, Bluetooth, LG TV and “LG Wi- Bluray disc player, set-top box or etc. device Fi Speaker” app and then changes suitable function set to on or connected CEC supported device automatically. is turned on. If you want to use the auto function change, When you turn on your TV or an turn off SIMPLINK function on your LG TV. external device It takes for about 30 seconds to turn off When you turn on your TV or an external device SIMPLINK. connected by the optical, LG sound sync (optical or yy If the Bluetooth connection lock function wireless) or HDMI ARC this sound bar will change is set, Bluetooth connection will be only to a suitable function so you can listen to the sound available on Bluetooth and LG TV function. through it. (Page 33) yy In WI-FI function without network connection, When you try to connect a Bluetooth you cannot connect Bluetooth device and LG 3 device TV through LG Sound Sync (Wireless). Operating When you try to connect your Bluetooth device to To make these connections, change to the this unit, Bluetooth function is selected. Play your appropriate function. music on the Bluetooth device. When you play music by “LG Wi-Fi Speaker” app When you play music by “LG Wi-Fi Speaker” app on your smart device, this sound bar changes the function to WI-FI and you can listen to the music through it.

Page 37

38 Operating Standby mode Bluetooth standby mode If the Bluetooth standby mode is set to ON, the The speaker switches to the standby mode if there is speaker switches Bluetooth standby mode when is no music playback or no button operation. turned off. When you turn on the main unit in the Bluetooth standby mode, Bluetooth and LG TV are able to Standby mode connect even if network is not connected. Option 1. Adjust volume level of the unit to minimum. And then, press and hold p on the unit and J on the If network is disconnected and there is no music remote control for about 3 seconds. You can see playback and no button operation for 15 minutes, “ON-BT STANDBY” and the unit switches Bluetooth the speaker switches to the standby mode. Then standby mode. “GOOD-BYE” appears on the display window. To cancel this function, press J on the remote control while “ON-BT STANDBY” is scrolled. 3 Option 2. If you press and hold 1 for about 3 seconds, the ,,Note Operating To use this function, you should turn on the speaker switches to the standby mode. Then “GOOD- AUTO POWER function. BYE” appears on the display window. And all wireless network ports are deactivated. Network standby mode Reset the Speaker Option 1. If the speaker doesn’t respond, reset the speaker. When network is connected but music is not played Press and hold the / on the unit until you hear and buttons are not pressed for 15 minutes, the the beep sound once. You can see “RESET” on the speaker switches to the network standby mode. display window. Then all the stored wireless network Then “GOOD-BYE” appears on the display window. information is deleted. Option 2. If you press 1, the speaker switches to the network standby mode. Then “GOOD-BYE” appears on the display window.

Page 38

Troubleshooting 39 Troubleshooting General Symptoms Cause & Solution The unit does not work yy Turn off the power of this unit and the connected external device (TV, Woofer, properly. DVD-player, Amplifier, etc.) and turn them on again. yy Disconnect the power cord of this unit and the connected external device (TV, Woofer, DVD-player, Amplifier, etc.) and then try connecting again. yy Previous setting may not be saved when device power is shut off. The power does not turn Is the power cord plugged into the outlet? on. yy Connect the power plug to the outlet. Sound is not produced. Is the volume set to minimum? yy Adjust the volume. yy When you are using connection with a external device (set top box, Bluetooth device etc.), adjust volume level of the device. 4 Is the mute function activated? Troubleshooting yy Press [ or adjust the volume level to cancel the mute function. Is the function selected properly? yy Check the input source and select the correct input source. No woofer sound Is the subwoofer plugged in? yy Plug the power cord of subwoofer into the wall outlet securely. Is pairing between the unit and the subwoofer disconnected? yy Connect the unit and the subwoofer. (Page 16.) The remote control does Is the remote control too far from the unit? not work properly. yy Operate the remote control within about 7 m. Is there an obstacle in the path of the remote control and the unit? yy Remove the obstacle. Are the batteries in the remote control exhausted? yy Replace the batteries with new one. The AUTO POWER yy Check connection of the external device such as TV, DVD/Blu-Ray player or function does not work. Bluetooth device. yy Check the state of SIMPLINK on your LG TV and turn off SIMPLINK. yy Depending on the connected device, this function may not operate. LG Sound Sync does not yy Check whether your LG TV supports LG Sound Sync. work. yy Check connection of LG Sound Sync. yy Check sound setting of your TV and this unit.

Page 39

40 Troubleshooting Symptoms Cause & Solution When you feel the output Check the details below and adjust the unit according to them. sound of the unit is low. yy Switch the state of DRC function to [OFF] by using “LG Wi-Fi Speaker”. yy With the sound bar connected with TV, change the AUDIO DIGITAL OUT setting on TV Setup Menu from [PCM] to [AUTO] or [BITSTREAM]. yy With the sound bar connected with Player, change the AUDIO DIGITAL OUT setting on Player Setup Menu from [PCM] to [PRIMARY PASS-THROUGH] or [BITSTREAM]. yy Change Audio DRC setting on connected device setup menu to [OFF] state. yy Make sure Night Time mode is not On. Turn [OFF] Night Time mode. Bluetooth pairing does yy Be sure your Bluetooth device is on. not work well. yy Switch Bluetooth off and on again on your Bluetooth device, then try pairing again. yy Remove the obstacle in the path of the Bluetooth device and the unit. yy Depending on the type of the Bluetooth device or surrounding environment, your device may not be paired with the unit. 4 The unit does not connect yy Turn off the Bluetooth connection lock function. (Page 33.) with Bluetooth device. Troubleshooting

Page 40

Troubleshooting 41 Network Symptoms Cause & Solution Cannot connect the yy The wireless communication may be interrupted from household devices that speaker to your home are using radio frequencies. Move the speaker away from them. network. yy Check your router. Try turning it off and back on. yy Check that the Wi-Fi feature is turned on in your smart device. yy Check that the speaker and your smart device are connected to same Wi-Fi. Media servers are not yy The firewall or anti-virus software on your media server is running. Turn off displayed on the device the firewall or anti-virus software running on your media server. list. yy Make sure that the speaker is connected to the same network that your media server is connected. Wi-Fi connection does If you restart the router? not work well. yy You need to turn the speaker’s power off and on again. If you install new router. yy You need to perform a factory set and setup the network connection for speaker. 4 Application Troubleshooting Symptoms Cause & Solution The application doesn’t Does an error occur when accessing the app? work properly. yy Make sure that your smart device is compatible with the app. yy Make sure that the application is the latest version. yy Make sure that the connected unit turns on.

Page 41

42 Troubleshooting NOTES to use wireless Symptoms Cause & Solution This device may have yy Wireless may not operate normally in weak signal area. wireless interference. yy Please install the device close enough to wireless subwoofer. yy Do not install the device on metal furniture for optimum performance. Bluetooth device may yy When any part of your body contact the transceiver of the Bluetooth device malfunction or make or sound bar. noise in the following yy When there is an obstacle or wall or the device is installed in a secluded spot. cases. yy When there is a device (a wireless LAN, a medical equipment or a microwave) using same frequency, make the distance between the products as far away as possible each other. yy When connecting the device to the Bluetooth device, make the distance between the products as close as possible each other. yy When the device gets too far from the Bluetooth device, the connection is disconnected and also malfunction may occur. 4 Troubleshooting NOTES to release Demo mode Symptoms Cause & Solution Can not change input source with F such as BT Unplug the power cord and plug it in again. If that (Bluetooth), HDMI etc. and only [DEMO] indication doesn’t work, press and hold F (About 5 seconds) on is showing in the front display. the main unit until the display indicates current selected function. Remote Control does not work. (No response)

Page 42

Appendix 43 File requirement Available File extensions: “.mp3”, “.flac”, “.aac”, “.ogg”, “.wav”, “.wma” Sampling frequency: within 32 to 48 kHz (mp3, wma), up to 192 kHz/24 bit (flac) Bit rate: up to 320 kbps (mp3) yy The file requirements are not always compatible. For DTS patents, see http://patents.dts.com. There may have some restrictions by file features Manufactured under license from DTS Licensing and media server’s ability. Limited. DTS, the Symbol, DTS and the Symbol yy Some wav files are not supported on this speaker. together, Virtual:X, and the DTS Virtual:X logo are registered trademarks or trademarks of DTS, Inc. in yy Depending on the types of file or ways of the United States and/or other countries. © DTS, recording, it may not play back. Inc. All Rights Reserved. yy Some DRM-loaded files are not supported on this speaker. yy The types of supported files may differ depending on the operating system and/or the manufacturer of the smart device and PC. The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by LG Trademarks and licenses Electronics is under license. Other trademarks and trade names are those of All other trademarks are trademarks of their their respective owners. respective owners. 5 Appendix The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI logo are Manufactured under license from Dolby trademarks or registered trademarks of HDMI Laboratories. Dolby, Dolby Audio, and the double-D Licensing LLC in the United States and other symbol are trademarks of Dolby Laboratories. countries. For DTS patents, see http://patents.dts.com. Manufactured under license from DTS Licensing Limited. DTS, the Symbol, DTS and the Symbol together, and Digital Surround are registered trademarks and/or trademarks of DTS, Inc. in the United States and/or other countries. © DTS, Inc. All Rights Reserved.

Page 43

44 Appendix Specifications General Power consumption Refer to the main label on the unit. Model: DA-50F25 Manufacturer: Asian Power Devices Inc. AC adapter Input: 100 - 240 V ~ 50 - 60 Hz Output: 25 V 0 2 A Dimensions (W x H x D) Approx. 1060.0 mm x 57.0 mm x 85.0 mm With foot Operating temperature 5 °C to 35 °C Operating humidity 5 % to 90 % Bus Power Supply (USB) 5 V 0 500 mA Available Digital Input Audio 32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 192kHz Sampling Frequency Available Digital Input Audio format Dolby Audio, DTS Digital Surround, PCM Input/Output OPTICAL IN 3 V (p-p), Optical jack x 1 HDMI IN 19 Pin (Type A, HDMI™ connector) x 1 HDMI OUT 19 Pin (Type A, HDMI™ connector) x 1 5 Amplifier (RMS Output) Appendix Total 420 W RMS Front 80 W RMS x 2 (4 Ω at 1 kHz, THD 10 %) Center 40 W RMS (4 Ω at 1 kHz, THD 10 %) Subwoofer 220 W RMS (3 Ω at 80 Hz, THD 10 %)

Page 44

Appendix 45 Wireless subwoofer Power requirements Refer to the main label on the subwoofer. Power consumption Refer to the main label on the subwoofer. Type 1 Way 1 Speaker Impedance 3Ω Rated Input Power 220 W RMS Max. Input Power 440 W RMS Dimensions (W x H x D) Approx. 171.0 mm x 393.0 mm x 248.5 mm System Wireless LAN (Internal antenna) 802.11a/b/g/n Wi-Fi networks SPK8-S (SPK8-S, S78S1-S), Sold Separately Wireless receiver Power requirements Refer to the main label on the wireless receiver. Power consumption Refer to the main label on the wireless receiver. Rear 70 W RMS x 2 (3 Ω at 1 kHz, THD 10 %) Dimensions (W x H x D) Approx. 60.0 mm x 220.0 mm x 175.0 mm Rear speakers (Each) 5 Type 1 Way 1 Speaker Appendix Impedance 3Ω Rated Input Power 70 W RMS Max. Input Power 140 W RMS Dimensions (W x H x D) Approx. 100.0 mm x 140.0 mm x 100.0 mm yy Designs and specifications are subject to change without prior notice.

Page 45

46 Appendix Handling the Speaker Important Information Relating to Network When shipping the speaker Please save the original shipping carton and packing Services materials. If you need to ship the speaker, for maximum protection, re-pack the speaker as it was All information, data, documents, communications, originally packed at the factory. downloads, files, text, images, photographs, graphics, videos, webcasts, publications, tools, resources, software, code, programs, applets, widgets, Keeping the exterior surfaces clean applications, products and other content (“Content”) yy Do not use volatile liquids such as insecticide spray and all services and offerings (“Services”) provided or near the speaker. made available by or through any third party (each yy Wiping with strong pressure may damage the a “Service Provider”) is the sole responsibility of the surface. Service Provider from whom it originated. yy Do not leave rubber or plastic products in contact The availability of and access to Content and with the speaker for a long period of time. Services furnished by the Service Provider through the LGE Device are subject to change at any time, Cleaning the speaker without prior notice, including, but not limited to the suspension, removal or cessation of all or any part of To clean the player, use a soft, dry cloth. If the the Content or Services. surfaces are extremely dirty, use a soft cloth lightly moistened with a mild detergent solution. Do not use Should you have any inquiry or problem related strong solvents such as alcohol, benzine, or thinner, to the Content or Services, you may refer to the as these might damage the surface of the speaker. Service Provider’s website for the most up-to-date information. LGE is neither responsible nor liable for 5 customer service related to the Content and Services. Any question or request for service relating to the Content or Services should be made directly to the Appendix respective Content and Service Providers. Please note that LGE is not responsible for any Content or Services provided by the Service Provider or any changes to, removal of, or cessation of such Content or Services and does not warrant or guaranty the availability of or access to such Content or Services.

Page 46

Appendix 47 TERMS OF USE We do not accept any responsibility if for any reason the Services or any part of them are unavailable at any time or for any period. These Terms of Use apply to those individuals and Although you may use LG Software to download and groups who use LG’s Wi-Fi speaker, any software(s) access content or applications made available by third associated with LG Wi-Fi speaker, this application and parties on your LG Software, we make no promises any services associated this application (collectively or guarantees that you will always be able to access “LG Software”). They set out LGE’s responsibilities such content or applications. So far as we are legally to you as well as identifying the “dos” and “don’ts” able to do so, we exclude any warranties, conditions that you should be aware of when you use the or other terms which may be implied into these LG Software. LG Software is proprietary software license terms by law. owned by LG Electronics Inc., a corporation registered So far as we are legally able to do so, we exclude any in Korea with its registered office at Yeouido-dong liability for any loss or damage incurred by you or 20, Yeoungdeungpo-gu, Seoul, Korea. LGE, and its any other person in connection with your use of LG licensors (“LGE”, “us” or “we”). Software. We are only responsible for loss or damage By accessing or using LG Software, you confirm that suffered that is a foreseeable result of our breach you accept these Terms of Use and that you agree to of these license terms or our negligence up to the comply with them. If you do not agree to these Terms amount specified below, but we are not responsible of Use, you may not access or use the LG Software. for any loss or damage that is not foreseeable . To the extent that any conflict arises between these Loss or damage is foreseeable if it is an obvious Terms of Use and any other document referred to consequence of our breach or if it was contemplated in these Terms of Use, these Terms of Use will take by you and us when you starting using LG Software. precedence, unless clearly stated otherwise in the For any loss or damage that is not excluded relevant document. under these license terms, whether in contract, We grant you a non-exclusive license to use the pre- tort (including negligence) or otherwise, the total installed copy of LG Software solely to the extent liability of us and our group of companies to you necessary for you to use your LG Wi-Fi speaker is limited to the amount that you paid for your LG 5 personally and for no other purpose. Software service. To the extent permissible under Appendix You acknowledge that all ownership rights in LG the applicable laws, some jurisdictions do not allow Software anywhere in the world belong exclusively to the limitation or exclusion of liability for incidental us and that no ownership rights in LG Software are or consequential damages, or have legislation that transferred to you. You are only entitled to the limited restricts the limitation or exclusion of liability, so the use of LG Software as is granted in these license above limitation may not apply to you. terms. Nothing is these license terms shall limit or exclude You may not copy, modify, decompile or reverse our liability for death or personal injury relating from engineer our software in any way unless you are our negligence, fraud or fraudulent misrepresentation allowed to do so by law. We reserve the right to or any other liability that cannot be excluded or suspend, withdraw or discontinue all or part of the limited by law. Services without notice if we consider that you are in LG Software provides access to “apps” and link to breach of these Terms of Use. other services owned and operated by third parties, You acknowledge that LG Software has not been such as content providers. Any third party apps, developed to meet your individual requirements. We services and content that you access via the Services make no promises or guarantees that LG Software are made available to you by these third party is free from bugs or errors or that it will always be providers and are outside the scope of these Terms of available. We use commercially reasonable efforts Use. to provide LG Software on a continuous, high quality Your dealings with any third party providers are solely basis but cannot guarantee that they will always be between you and the relevant provider and may be available, uninterrupted or error free. It is possible subject to the provider’s own terms and conditions that we may have to interrupt or discontinue the LG and privacy policy. We encourage you to read these Software or suspend or restrict your use of all or any documents, although we are not responsible for their part of the Services where we consider it reasonably content. We do not accept any responsibility for apps, necessary for technical, operational, security, legal or services or content provided by third party providers. regulatory reasons.

Page 47

48 Appendix We may impose limits on the use of or access to Modify as you think appropriate: Complaints certain third party content, application or services, If you have any queries, concerns or complaints in any case without notice or liability. We expressly about the Services, please contact [include reference disclaims any responsibility or liability for any change, to non-personal LG email address]. interruption, disabling, removal of or suspension of any content, application or service made available Modify as you think appropriate: Miscellaneous through this LG Software. We are neither responsible Unless expressly stated otherwise, these Terms of nor liable for customer service related to the content, Use and the documents referred to in them contain application and services. Any question or request for the entire agreement between us and you relating service relating to third party’s content, application to your use of the Services and supersede any or services should be made directly to the respective previous agreements, arrangements, undertakings content and service providers or application or proposals, written or oral, between us and you developers, as appropriate. relating to your use of the Services. These terms do not affect your statutory rights as a We may assign, sub-contract or otherwise transfer consumer. any or all of our rights and obligations under these Suitability of the Services for children and parental Terms of Use to any company, firm or person. We control tools can only do this if it does not materially affect your rights under these Terms of Use. You may not assign, Modify this accordingly to suit if appropriate: The sub-contract or otherwise transfer your rights or Services are not directed at children under the age obligations under these Terms to anyone else (except of 13 and are not structured specifically to attract where you dispose of your LG Smart TV to a third children under 13. Further, certain content that party) unless you first agree this with us in writing. you may access through your use of the Services may contain material that you consider indecent, If we decide not to exercise or enforce any right that objectionable or which may not be suitable for we have against you at a particular time, then this children. does not prevent us from later deciding to exercise or enforce that right. If you permit a child to use your LG Smart TV to 5 access the Services, you are solely responsible for If any part of these Terms of Use is found to be deciding whether or not the relevant Services are illegal, invalid or otherwise unenforceable by a court Appendix appropriate for access by that child. or regulator, then, where required, that part shall be deleted and the remaining parts of the Terms of Use [Your Smart TV offers a parental control tool (by will continue to be enforceable. way of a 4 digit PIN). If you have enabled the 4-digit PIN, your LG Smart TV will not be able to display These Terms of Use do not create or infer any rights restricted content unless you type in the PIN. You that are enforceable by any person who is not party are responsible for setting up and maintaining the to them. parental control tool and any other controls that are These Terms of Use are governed by the laws of the available, and we will not be responsible for any harm, country where your LG Smart TV is sold and both you loss or damage you suffer or any other user of your and LGE agree to submit to the exclusive jurisdiction LG Smart TV suffers as a result of your failure to do of the courts of the country where your LG Smart TV so. Depending on the models of your LG Smart TV, is sold in connection with the same these features may not be available. This Agreement shall be governed by the laws of the Viruses and Security Republic of Korea, excluding their conflicts of laws Modify this accordingly to suit if appropriate: We use provisions. commercially reasonable efforts to ensure that the If you have any questions or comments about these Services are secure and virus free, but those efforts Terms of Use please contact www.lg.com. cannot and do not guarantee that the Services will be These Terms of Use may be updated by LGE from free from bugs, viruses, or other vulnerabilities. time to time. If we make a material change to Further, we do not accept responsibility for any loss our Terms of Use, we will update you via your LG or damage caused by a virus, distributed denial- Software or other means. of-service attack, or other technologically harmful material that may infect your LG Smart TV, data or other material belonging to you, during your use of the Services.

Page 48

Appendix 49 OPEN SOURCE SOFTWARE NOTICE INFORMATION To obtain the source code under GPL, LGPL, MPL, and other open source licenses, that is contained in this product, please visit http://opensource.lge.com. In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are available for download. LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such distribution (such as the cost of media, shipping, and handling) upon email request to [email protected] This offer is valid for a period of three years after our last shipment of this product. This offer is valid to anyone in receipt of this information. 5 Appendix

Page 49

OWNER’S MANUAL LG Wi-Fi Speaker Connection www.lg.com 1901_Rev01 Copyright © 2019 LG Electronics Inc. All Rights Reserved.

Page 50

2 Connection Connecting the Speaker Simple Connection to your Home Network Preparation yy For Simple Connection, Wi-Fi network condition is needed. Requirements yy Make sure that the Bluetooth setting on your smart device in on. yy A wireless router must be connected to the internet. yy Select WI-FI function by using F on the remote control or F on the speaker. yy A smart device such as a smartphone or tablet must be connected to the wireless router via Wi- Fi connection. ,,Note Simple Connection is supported by Bluetooth ,,Note Ver 4.0 (or higher). yy Make sure that DHCP’s server is activated on wireless router. 1. Check the position and condition of the speaker yy If you cannot connect the speaker with your and select [Next]. router, go to setting of the router and then make sure that “Allow wireless client to see each other and access my local network” box is unchecked. yy In a network environment (Router, Internet and Internet Service Provider) that supports both IPv4 and IPv6, the network automatically connects to IPv4 or IPv6 when connecting to the network. You can check the each network status by selecting the settings of My Speakers ([ ]>[IP Info.]) on “LG Wi-Fi Speaker” app. If you use Android device, Location authorization is needed. Go to the next step if you use iOS device. Allow the Location authorization. And then press [Next] again.

Page 51

Connection 3 2. Then you can see the available speaker to 4. If you have a password for your network, the connect. security screen appears on your smart device. Enter your password and tap [Next]. -- Select [ ] if the desired speaker doesn’t appear. -- Select [ ] to check the speaker with a beep 5. Tap [OK] to finish making the connection. sound. -- Search failed, select [Retry] to search your speaker again or connect the speaker manually. (page 4) 3. Select the speaker to connect by checking [ ] and [Next].

Page 52

4 Connection Manual connection 3. This step is only for iOS device. Go to the next step if you use Android device. When the simple connection is unavailable between Turn on Wi-Fi setting on your iOS device and your speaker and smart device, you can connect it choose [LG_Speaker_Setup_XXXX] and then go manually. back to “LG Wi-Fi Speaker” app. 1. Select [Manual setup] to connect the speaker manually. 4. Enter your password and tap [Next]. 2. Check the position and condition of the speaker and select [Next]. Then your smart device is searching for the available speaker to connect. 5. Tap [OK] to finish making the connection.

Page 53
Load More
Recent Documents


Owner's manual - Clarion

Owner's manual NX602 DVD MULTIMEDIA STATION WITH BUILT-IN NAVIGATION & 6.2" TOUCH PANEL CONTROL English 1 NX602 Contents English Thank you for purchasing this Clarion product. • Please fully read th

Read More

Lg Smart Tv User Guide Pdf

Lg Smart Tv User Guide Pdf Slaked Parker journalize: he fagged his Alexandra overfondly and greenly. Mussier and curvilinear Gretchen still negotiate his solemnity irreparably. Acronychal and ulmaceou

Read More

ANUARIO 2008 - Inba Digital

ANUARIO 2008 TEATRO EN LOS ESTADOS TEATRO EN LOS ESTADOS ANUARIO 2008 CONSEJO ESTATAL PARA LA CULTURA Y LAS ARTES HIDALGO GOBIERNO DEL ESTADO Veracruz late con fuerza Instituto Veracruzano de la Cultu

Read More

Microsoft Word - 03_antrop.doc

3 From holistic landscape synthesis to transdisciplinary landscape management Marc Antrop Abstract The concept of ‘landscape’ has multiple meaning and is intrinsically holistic. Since the Renaiss

Read More

14221-1510-2000, Rev. K, XG-25M Mobile Radio; Operator's Manual

Operator’s Manual 14221-1510-2000 Rev. K, June 2019 XG-25M Mobile Radio 14221-1510-2000, Rev. K MANUAL REVISION HISTORY REV. DATE REASON FOR CHANGE D Oct/14 Updated for XGP R4A; added Voice Annuncia

Read More

Grade 10 Life Sciences Paper 3 (Exemplar)

NATIONAL SENIOR CERTIFICATE GRADE 10 LIFE SCIENCES P3 (PRACTICAL) EXEMPLAR 2012 MARKS: 60 TIME: 1 hour This question paper consists of 4 pages. Copyright reserved Please turn over Life Sciences/P3 (Pr

Read More

Moving Toward a Reparative Archive: A Roadmap for a Holistic Approach to Disrupting Homogenous Histories in Academic Repositories and Creating Inclusive Spaces for Marginalized Voices

Journal of Contemporary Archival Studies Volume 5 Article 6 2018 Moving Toward a Reparative Archive: A Roadmap for a Holistic Approach to Disrupting Homogenous Histories in Academic Repositories and C

Read More

Microsoft Word - LAH 6934 fall 2016 syllabus.doc

LAH 6934: Colonial Spanish America Ida Altman T 8-10 (3-6 p.m.), Keene-Flint 13 Office: Grinter Rm. 339 Email: [email protected] Hours: Th 10-12 The objective of the seminar is to become familiar with t

Read More

NB3520A-NB_DUSALLK_ENG_6160.indd

OWNER’S MANUAL 300W Sound Bar System Please read this manual carefully before operating your set and retain it for future reference. NB3520A (NB3520A, SHS36-D) www.lg.com NB3520A-NB_DUSALLK_ENG_6160

Read More

grade-10-english-fal-paper-1-exemplar-2006.pdf

NATIONAL SENIOR CERTIFICATE GRADE 10 ENGLISH FIRST ADDITIONAL LANGUAGE P1 EXEMPLAR PAPER - 2006 MARKS: 75 TIME: 2 hours This question paper consists of 12 pages. Copyright reserved Please turn over En

Read More

Teatro - Inba Digital - Instituto Nacional de Bellas Artes

Teatroen los estados 2013 TEATRO EN LOS ESTADOS ANUARIO 2013 Te atro en l os E sta dos 2013 es una publicación de Teatromexicano punto com AC en coedición con: Centro Cultural Tijuana Centro Naciona

Read More

Thesis Template - TSpace

Conquering Creoles: Power, Transculturation, and the Limits of Empire in New Spain, 1521-1625 by Lindsay Christine Sidders A thesis submitted in conformity with the requirements for the degree of Doct

Read More

Seguridad Humana y capital emocional

See discussions, stats, and author profiles for this publication at: https://www.researchgate.net/publication/212684226 Aproximación filosófica El educacionismo como síntoma psicológico de la Se

Read More

PMM WORKS, INC. COMPANY PROFILE

PMM WORKS, INC. POWER, MANUFACTURING & MARINE WORKS, INC. ( PCAB License No. 37361 ) COMPANY PROFILE YEAR 2021 200 Don Gregorio Ave. Almanza I, Las Piñas City Tel. No.: (02) 8874-8844/8823-5654/8556-

Read More

USER MANUAL LG MultiSITETM VM3 - LG HVAC

LG MultiSITETM VM3 USER MANUAL Model Number: PBACNBTR1A (PBACNBTR1 + ZSMA01BMS) PROPRIETARY DATA NOTICE This document, as well as all reports, illustrations, data, information, and other materials are

Read More

Indigenous Masculinities and the Tarascan Borderlands in Sixteenth-Century Michoacán

University of Texas at El Paso [email protected] Open Access Theses & Dissertations 2019-01-01 Indigenous Masculinities and the Tarascan Borderlands in Sixteenth-Century Michoacán Daniel Santana Univ

Read More

LG_G_PAD_IV_BI.pdf

ENGLISH FRANÇAIS USER GUIDE LG-V533 Copyright ©2017 LG Electronics, Inc. All Rights Reserved. MFL70204601 (1.0) www.lg.com ENGLISH About This User Guide Thank you for choosing LG. Please carefully r

Read More

Sufism - Oxford Islamic Studies Online

Sufism - Oxford Islamic Studies Online http://www.oxfordislamicstudies.com.myaccess.library.utoronto.ca/print/... Citation for Sufism Citation styles are based on the Chicago Manual of Style, 15th Ed.

Read More

LG-L125DL_TRF_UG_EN_V10_200203.pdf - Page Plus

ENGLISH USER GUIDE LG L125DL Copyright ©2020 LG Electronics Inc. All Rights Reserved. MFL71687601 (1.0) www.lg.com ENGLISH About this user guide Thank you for choosing this LG product. Please careful

Read More

Colonial Spanish Sources for Indian Ethnohistory - Newberry Library

Colonial Spanish Sources for Indian Ethnohistory at the Newberry Library edited by Gabriel Angulo, M.A LIS Colonial Spanish Sources for Indian Ethnohistory NEW WORLD General Sources. . . . . . . . . .

Read More

Comecei a amar-te no dia em que te abandonei. - fnac-static.com

Comecei a amar-te no dia em que te abandonei. Foram as palavras dele quando, dez anos depois, a encontrou por mero acaso no café. Ela sorriu, disse-lhe «olá, amo-te» mas os lábios só dis- seram

Read More